Monza R6 On-Metal RFID Tag, 40 × 25 × 0.75 mm: spec drawing (UHF, Impinj Monza R6, 40 × 25 mm)

AZ-R6-40X25M

Monza R6 On-Metal RFID Tag, 40 × 25 × 0.75 mm

A 40 × 25 mm on-metal RFID label with Monza R6, only 0.75 mm thick, built to read when mounted directly on metal.

Validate samples first. Engineer reply within 24 h.

Check suitability for your application

See the sample validation checklist

Specifications
SKU AZ-R6-40X25M
Frequency UHF 860–960 MHz
Protocol EPC Gen2v2 (ISO/IEC 18000-63), RAIN RFID
Chip Impinj Monza R6
Memory 96-bit EPC, serialized 96-bit TID, no user memory
Chip read sensitivity −22 dBm (vendor reference) Vendor-specified measurement conditions; not finished-tag performance
Chip status Impinj lists Monza R6 as end-of-life; ask us about current alternatives before a new design.
Antenna size 40 × 25 mm
Thickness 0.75 mm
Format On-metal label
Read range up to 3 m (reference) depends on reader, antenna, power and the tagged material
Typical applications Metal assets & IT

Design and application notes

Monza R6 On-Metal RFID Tag, 40 × 25 × 0.75 mm is a UHF on-metal RFID label built around the Impinj Monza R6 chip, measuring 40 × 25 × 0.75 mm. A standard inlay stuck directly on steel or aluminium is detuned and usually cannot be read; this label uses a foam spacer to hold the antenna away from the surface while staying only 0.75 mm thick, so it can be mounted directly on metal.

Impinj Monza R6 provides 96-bit EPC, serialized 96-bit TID, no user memory. Impinj lists read sensitivity of −22 dBm and write sensitivity of −17 dBm as vendor reference values (Vendor-specified measurement conditions; not finished-tag performance). Validate the complete tag with samples on the intended item and reader setup. Datasheet highlights: AutoTune adaptive RF tuning, Integra memory diagnostics, Enduro bonding pads, FastID and TagFocus. Please note: Impinj lists Monza R6 as end-of-life; ask us about current alternatives before a new design.

Our reference figure for this design is up to 3 m (reference). Range depends on the reader, antenna, power and tagged material; test samples in your own setup before you commit to volume.

Typical mounting surfaces are IT equipment, tools, metal containers and machine parts. Apply it to a flat, clean metal area; the label is tuned for metal, so on plastic, wood or cardboard a standard UHF inlay is usually the better and cheaper choice.

It ships as a foam-spacer on-metal label; face printing (asset numbers, logos, barcodes), EPC encoding and other sizes are quoted on request. We send samples first so you can test on your own metal parts, and volume orders are produced with our ISO 9001-certified production partner with 100% inline electrical testing.

Specification basis and validation

Vendor documents describe the chip, not finished-tag read range.

Confirm catalog dimensions against the final tag construction. Reference read ranges require sample testing on your item with your reader setup.

Order in the format you need

Confirm the construction and encoding during sampling, then quote the configuration you validated.

  • On-metal label

    Antenna and chip over a foam spacer with adhesive back, for flat metal surfaces.

  • Printed face

    Asset numbers, logos, barcodes or QR codes printed on the face stock.

  • Pre-encoded

    EPC written to your numbering scheme before shipping, locked on request.

  • Custom

    Other sizes or thicknesses assessed and quoted on request, validated with samples.

What should the sample pass before a bulk order?

Agree the actual use conditions and pass criteria before selecting samples. The catalogue supports shortlisting; confirm finished-tag performance and delivery configuration in writing and through sample validation.

  1. Test on the finished metal item

    Record the metal material, dimensions, curvature, assembly state and mounting position. Fix reader and antenna settings, use the final spacer, face stock and adhesive, and define the intended read zone.

  2. Check reads, identity and mounting separately

    Check unique identities inside the target zone and unintended reads outside it. Read back the EPC against printed IDs. Inspect lifting edges, adhesion and behavior after relevant handling; record separate acceptance decisions.

  3. Record the approved construction and delivery configuration

    Record the SKU, sample revision, lot, device settings, results and approver. Confirm final dimensions, materials, printing, encoding, quantity and delivery requirements, and agree which configuration changes require another trial.

Use the test record to save actual conditions and results. English and Chinese worksheets are provided; the agreed reviewer determines acceptance.

Download test record

How ordering works

  1. 01

    Specify

    Share surface, read distance, chip preference and volume. We shortlist tags that fit.

  2. 02

    Sample

    Receive sample tags of the shortlisted designs to try in your own setup.

  3. 03

    Validate

    Test on your items, readers and printers. We adjust chip, size or format if needed.

  4. 04

    Produce & ship

    Volume production with 100% inline electrical test, then export shipping.

Frequently asked questions

Can the AZ-R6-40X25M be printed and encoded?

Yes. The face stock can carry asset numbers, logos or barcodes, and we can write your EPC numbers before shipping. Other sizes are quoted on request; see custom tags.

What read range will I get with the AZ-R6-40X25M?

Our reference value is up to 3 m (reference). Real-world range depends on the reader, antenna, power and the tagged material (including the size and shape of the metal surface), so we recommend testing samples in your setup. More in our read range guide.

How do I get samples and a quote for the AZ-R6-40X25M?

Use the quote button on this page or request samples. Tell us the item, surface, read distance and annual volume; an engineer replies within 24 hours with a recommendation and a sample plan.

Talk to an RFID engineer

Not sure which tag fits your project?

Send the surface, read distance and volume. An engineer replies within 24 hours with a recommendation and a sample plan.

Email us: sales@antenza.com

Quick quote

Monza R6 On-Metal RFID Tag, 40 × 25 × 0.75 mm

AZ-R6-40X25M

Tell us the quantity and where the tag goes. We reply within 24 hours.

For a quote, share the tagged item, mounting surface, metal type, required read distance, reader model, quantity, and printing or encoding needs.

An engineer replies within 24 hours.

By sending this form you agree to our privacy policy. We use your details to answer and follow up on this inquiry.

Cloudflare Turnstile checks submissions to prevent spam.

Email us Get a quote